Equal-Cost Multipath (ECMP) is fundamental to data center fabric design. It maximizes link utilization and builds in redundancy without complex failover logic. In an EVPN-VXLAN overlay, ECMP works at both the underlay (between leaf and spine switches) and the overlay (across multiple hypervisors hosting the same service).
This two-part series covers overlay ECMP using EVPN with VXLAN encapsulation in OcNOS. Part 1 establishes the topology and configuration for distributing traffic across multiple hypervisors. Part 2 extends this to advanced multi-hypervisor scenarios.
Data Center Clos Topology

How Overlay ECMP Works
In a standard EVPN-VXLAN fabric, each hypervisor advertises its locally hosted VMs via BGP EVPN. When multiple hypervisors host VMs with identical IP addresses (a common pattern for web-tier microservices with anycast VIPs), the leaf switches receive multiple EVPN route type-5 (IP prefix) advertisements for the same IP prefix, each from a different VTEP.
OcNOS installs all equal-cost VTEP routes as ECMP next-hops in the forwarding table. Ingress traffic is hashed across all VTEPs using a 5-tuple hash (source IP, destination IP, source port, destination port, protocol), distributing load without requiring a load balancer in the data path.
The configuration below is an illustrative reference. IP addresses, VNIDs, and interface names are consistent placeholders; substitute the values for your fabric.
Underlay Configuration: BGP EVPN Spine
! OcNOS Spine-1: BGP Route Reflector for EVPN
!
router bgp 65000
bgp router-id 10.0.0.10
bgp cluster-id 10.0.0.10
!
! Reflect EVPN routes to all leaf peers
neighbor LEAF-PEERS peer-group
neighbor LEAF-PEERS remote-as 65000
neighbor LEAF-PEERS update-source lo
neighbor LEAF-PEERS route-reflector-client
!
neighbor 10.1.1.1 peer-group LEAF-PEERS ! Leaf-1
neighbor 10.1.1.2 peer-group LEAF-PEERS ! Leaf-2
neighbor 10.1.1.3 peer-group LEAF-PEERS ! Leaf-3
!
address-family l2vpn evpn
neighbor LEAF-PEERS activate
neighbor LEAF-PEERS route-reflector-client
exit-address-family
!
commit
Overlay Configuration: EVPN-VXLAN on Leaf (OcNOS)
! OcNOS Leaf-1: EVPN-VXLAN with overlay ECMP
!
! Step 1: Enable VXLAN and set the global VTEP source IP
nvo vxlan enable
nvo vxlan vtep-ip-global 10.1.1.1 ! VTEP IP (loopback)
!
! Step 2: Create the VXLAN network identifier (VNID)
nvo vxlan id 10100 ingress-replication ! VNID 10100
!
! Step 3: Map an access interface/VLAN to the VNID
nvo vxlan access-if port-vlan 100
map vnid 10100 ! VLAN 100 -> VNID 10100
!
! Step 4: Use EVPN-BGP as the host-reachability control plane
vxlan host-reachability-protocol evpn-bgp
!
! Step 5: BGP EVPN - advertise and receive routes
router bgp 65000
bgp router-id 10.1.1.1
neighbor 10.0.0.10 remote-as 65000 ! Spine-1 (RR)
neighbor 10.0.0.10 update-source lo
neighbor 10.0.0.11 remote-as 65000 ! Spine-2 (RR)
neighbor 10.0.0.11 update-source lo
!
address-family l2vpn evpn
neighbor 10.0.0.10 activate
neighbor 10.0.0.11 activate
exit-address-family
!
! Step 6: Enable ECMP (multiple equal-cost next-hops per prefix)
router bgp 65000
address-family l2vpn evpn
maximum-paths 8 ! install up to 8 ECMP paths
exit-address-family
!
commit
!
! Verify: IP-X (web service VIP) should be learned from
! VTEP 10.1.1.1, 10.1.1.2, and 10.1.1.3
show bgp l2vpn evpn
!
show nvo vxlan
show nvo vxlan tunnel
Verifying ECMP Load Distribution
! OcNOS: Verify overlay ECMP is active
!
! Check ECMP paths installed in the routing table for IP-X:
show ip route 192.168.100.10/32 ! IP-X host route
!
! Check VXLAN tunnels per remote VTEP:
show nvo vxlan tunnel
!
! Review EVPN control-plane state:
show bgp summary
show bgp l2vpn evpn
Continue with Part 2: Advanced multi-hypervisor ECMP scenarios, where we increase VM density per hypervisor and explore how OcNOS handles subnet advertisement changes.
IP Infusion Engineering Team
Approfondite. Portatelo con voi.
Il datasheet di prodotto e download tecnici e sintetici che vanno oltre questa pagina.
Datasheet OcNOS-DC
Specifica completa di OcNOS-DC: il set di funzionalità EVPN-VXLAN e Ethernet for AI, gli SKU software, le piattaforme hardware supportate e la guida all'ordine della soluzione.
Ottieni il datasheetEVPN-VXLAN data center fabric
Fabric leaf-spine per data center di livello carrier: IRB simmetrico, route Type-2/Type-5 e gateway anycast distribuito.
Scarica il briefOcNOS 800G Lossless AI Fabric
Fabric RoCEv2 non bloccante su spine Broadcom Tomahawk 4/5: tier di SKU, piattaforme validate e architettura di deployment.
Scarica il briefDatasheet OcNOS-DC
Modulo rapido. Il suo PDF si apre in una nuova scheda subito dopo l'invio.
✓ Apertura del suo PDF in una nuova scheda…
Se non si è aperto, utilizzi il link qui sotto.
EVPN-VXLAN data center fabric
Modulo rapido. Il suo PDF si apre in una nuova scheda subito dopo l'invio.
✓ Apertura del suo PDF in una nuova scheda…
Se non si è aperto, utilizzi il link qui sotto.
OcNOS 800G Lossless AI Fabric
Modulo rapido. Il suo PDF si apre in una nuova scheda subito dopo l'invio.
✓ Apertura del suo PDF in una nuova scheda…
Se non si è aperto, utilizzi il link qui sotto.